1. how to change honda water pump water seal and impeller
#honda water pump #wb20xt#wb30x
2. Honda GX 160 Engine / Pump repair #poolseason #swimmingpool
How to repair your Honda GX160 water transfer pump.
The outer ring gear on mine had jumped time, only needed to be clocked back in time to make the pump run again.
Thanks for watching
Cheers
-Johnny
3. How to install a rebuild kit in a Honda 2 Pump
I show how to rebuild my Honda pump. This video didnt quite turn out right but it shows the basics of installing the rebuild kit.
4. EASILY Fix Your Honda Water Pump that is NOT Pumping
In "The Stuhl Sample" another hilariously informative how-to video, Taryl shows us how to properly install a shim washer on a Honda Water Pump. It may take a few tries with different shim sizes until you find the right one that works without it rubbing, but Taryl shows you what to do and how to get the job done right. Make sure you wash your hands before your dinner on THIS how-to on how to fix a non-pumping water pump! Be sure to 'Like' us on FaceBook and Subscribe to our channel for all the latest updates and info!
Please Subscribe to the channel and Thumbs Up our videos and be sure to 'Like' Us on Facebook for all the latest news and updates!
You can pick up all your TARYL APPAREL here: tarylfixesall.bigcartel.com
(T-Shirts, Coffee Mugs, Shop Products and More!) Shippping worldwide and daily!
LIKE us on FACEBOOK! facebook.com/tarylfixesall
We're on INSTAGRAM too! @tarylfixesall
5. This easy How to clean a Honda carburetor of small engine Gx160
How to clean a honda carburetor gx160
Small engine honda carburetor clean and repair
The easiest way to repair and - How to Remove the Carburetor
Dissect the Carburetor on - Clean the Parts the Carburetor clean the carburetor of the model GX160 engine
How to Repair and Cleaning the Carburetor
Test for Gas at the Carburetor
Some of the Processes in this restoration include Sanding, Sharpening, Buffing, Polishing, grinding, cutting, sawing, slicing.
I Make Videos centered around repair and Restoration, lawnmowers, brush cutter, chainsaw, motors, water pumps, hedge trimmer, sprayer pumps,
I hope you like my work and the video.
Ahmed Adel
The content of the channel is the restoration and repair of landscaping equipment and agricultural equipment
You can watch videos from the links
Don't forget to subscribe
How To Power Sprayer Pump Repairing : youtu.be/XW-Zl9eQPkQ
How To Repair the Carburetor : youtu.be/zEekxPl1v5o
How to repair pull starter : youtu.be/IsBxfKoExCU
How to Install Piston Rings Easily : youtu.be/SXY5WLt30NU
#Handicraft
#reparing_show
#restoration
6. Auction invite, Honda GC160, GX160 5HP engines and eBay parts,
5_12_2017, Auction invite, Honda GC160, GX160 5HP engines and eBay parts, wanted to put the "new Predator" engine back together, got $30 worth of eBay parts, have the recoil and plug replacements, used parts on trash pumps, 2 engines floating around the hoard, one may have a rod knock, Harvey Spooner, Hoarding Mayhem,
7. Water Pump Repair - Loose Bolts from Factory
Water Pump Repair - Loose Bolts from Factory
I like these little pumps a lot. They are very affordable, and in the instance that you have to work on them, they are super simple. Unfortunately, I had to do some work on this one.
It was leaking, and making that grinding noise before it quit. Come to find all the bolts holding the housing to the engine were loose, and 2/4 had backed out entirely, jamming up the impeller. I could not put them back in due to the thread getting marred, but was able to tighten down the other two and the pump ran great for well over an hour after that.
I checked the bolts on the other pump, which was actually leaking even worse, and they were all tight, so that one is a mystery. I snugged one or two of them, maybe a 1/4 turn. But it seems the leaking is less now, so maybe there was just a seal in there that needed to seat properly. Ultimately, I little leak is not an issue, so long as the bolts are all properly tight.
8. how to change honda wb30X water seal
#hondawaterpump#Wb30#wb20xt#waterseal
9. Repairing a Trash Water Pump
Repairing a Powerhorse 3 inch full trash water pump. This trash pump had been stored outside with the fuel cap off. There was water, debris, and rusty sludge in the tank and the pump housing was a mess. See the links below for the parts and tools I used:
Spark Plug:
amzn.to/2NLvTiP (affiliate*)
Copper BBs:
amzn.to/2Jv7WGM (affiliate*)
*Purchasing from these Amazon affiliate links earns my channel a small commission. Think of it as a tip that doesn't cost you anything. Thanks for the support!
10. Starting a Honda GX160 Engine
Anderson Industrial Engines is the Honda Distributor in the Midwest.
Welcome back to our AIE tutorial series to help you get to know your Honda GX 160. Today we are going to be learning to start the Honda GX160UT2QX2. Before starting your engine, check your fuel, oil level, and filter to ensure the engine is ready to use. All honda engines use 87 octane and above gasoline.
First, confirm that the on/off switch on the side of the engine is set to the on position. The black fuel valve should be slide all the way to the right which is set to the on position, and shut the choke by sliding the grey choke lever all the way to the left.
Before starting, make sure the throttle lever is slid to the right towards the turtle icon.
Pull the recoil handle, which will start the engine. While the engine is running in the idle position, slide the grey choke lever to the right to turn off the choke.
Once the engine is running, you may increase the RPM as needed by sliding the throttle to the left.
To turn the engine off, set the throttle back to the right starting position, and set the on/off switch to off.
For more information on Honda Engines, please read the description below, and visit us at ai-engines.com
11. Freeing a stuck Honda trash pump
Unclogging a stuck trash pump
12. How to prime a petrol water pump/ water pump not pumping water
In this video I'm demonstrated how to prime a centrifugal petrol water pump or a diesel water pump
Before starting up your water pump make sure that you fill water at the top of your gasoline/diesel water pump and usually the combustion water pump will come with water filler plug at the top, So you take out that cover and Start to pour water from the top until water comes out of the discharge hose
Once the crankcase is fully and water gets out of the discharge hose the priming process will be completed. You can also start by pour water along the suction hose until it's full of water then immediately dip that suction hose into the water
Start up your engine or switch on your water pump and wait for sometimes for the pump to pick up the water and Start pumping
If the pump didn't pump out water for long time let's say five minutes and water has not yet get out of the discharge hose something might be wrong with the priming process, make sure that the suction hose is well tighten to the water pump and no air gets inside the suction side of your pump
The purpose of priming the centrifugal pump is to remove any air that is inside the crankcase and suction hose as well
Don't remove the suction hose out of the water during pumping operations as that will destroy priming process by allowing air to enter the suction hose also make sure that the water level doesn't fall below the suction hose as that will also make water pump to run without pumping water
#How to prime petrol water pump
#centifugal water pump priming
13. Water pump diesel laging problema!
Troubleshooting of diesel water pump engine. Mechanical seal and injection pump.
need spare parts?
shoppee store
shopee.ph/powermaxx23?smtt=0.0.9
shoppee store
shopee.ph/japan_powermax_trading?v=d41&smtt=0.0.5
lazada store
Powermax Agri Machineries | s.lazada.com.ph/s.3eEq3
14. honda wb20xt semi trash pump repair
my trash pump quit pumpin so let's have a look....
15. Proper Water Pump Removal & maintenance
This shows you how to remove a pump impeller the right way along with other good tips. This is a complete pump and air compressor pulley removal for all 3hp to 6.5hp motors.